進口高壓?jiǎn)蜗蜷y質量耐用德國洛克

進口高壓?jiǎn)蜗蜷y性能范圍：

公稱通徑:DN3~DN80

適用溫度:-40℃～200℃

壓力范圍:PN16-PN420

連接方式:對焊、螺紋、卡套、活接、法蘭

適用介質:石油天然氣LNG CNG油﹑水﹑氣等多種非腐蝕性或腐蝕性介質

制造材料:20#﹑1Cr18Ni9Ti﹑F304﹑F316﹑F316L

進口高壓?jiǎn)蜗蜷y產品特點：

1.在生產中經過嚴格的止回實驗處理,能起到完全的止回作用

2.個部件均經過特殊的拋光處理,密封件采用進口材料,降低止回過程中的噪音,真正做到環保節能

3.它的閥瓣和閥座的密封面采用不同硬度的硬質合金噴焊而成

4.密封可靠,硬度高,耐磨耐高溫,抗擦傷性能好,壽命長

進口高壓?jiǎn)蜗蜷y產品概述：

德國《DE LOCKE》洛克-進口高壓?jiǎn)蜗蜷y是指采用不銹鋼或者碳鋼材質，采用整體鍛造，彈簧作用，耐高壓的單向閥，靠管路中介質本身的流動產生的力而自動開啟和關閉的，屬于一種自動閥門。單向閥用于管路系統，其主要作用是防止介質倒流、防止泵及其驅動電機機反轉，以及容器內介質的泄放。焊接式單向閥只允許介質向一個方向流動，而且阻止方向流動。

進口高壓?jiǎn)蜗蜷y安裝要點：

1、單向閥安裝位置、高度、進出口方向必須符合設計要求，注意介質流動的方向應與閥體所標箭頭方向一致，連接應牢固緊密。

2、閥門安裝前必須進行外觀檢查，，安裝前應進行強度和嚴密性能試驗，合格后方準使用。強度試驗時試驗壓力為公稱壓力的1.5倍，持續時間不少于5min，閥門殼體、填料應無滲漏為合格。嚴密性試驗時，試驗壓力為公稱壓力的1.1倍；

3、在管線中不要使單向閥承受重量，大型的單向閥(ae t v  One-way valve)：應du立支撐，使之不受管系產生的壓力的影響。

Installation points of imported high pressure check valve:
1. The installation position, height, inlet and outlet direction of one-way valve must meet the design requirements. The direction of medium flow shall be consistent with the arrow direction marked on the valve body, and the connection shall be firm and tight.
2. The appearance inspection must be carried out before the valve is installed, and the strength and tightness test shall be carried out before the valve is installed, and the valve can only be used after it is qualified. During the strength test, the test pressure shall be 1.5 times of the nominal pressure, and the duration shall not be less than 5min. The valve shell and packing shall be qualified if there is no leakage. In the tightness test, the test pressure is 1.1 times of the nominal pressure;
3. Don't make the check valve bear the weight in the pipeline. Large one-way valve should be supported vertically so that it is not affected by the pressure generated by the piping system.